/ Register

  1. Welcome to Taxidermy.net, Guest!
    We have put together a brief tutorial to help you with the site, click here to access it.

Degrease setup help

Discussion in 'Skulls and Skeletons' started by WolfGirl, Oct 15, 2016.

  1. Oct 15, 2016 #1
    WolfGirl

    WolfGirl Member

    615
    3
    Kirksville, Missouri
    So I finally got around to getting a decent degrease setup made. I got a water heater thermostat and element. I'm currently using a plastic tote. I drilled holes for the thermostat, drain, and element. I'm having issues getting it all to seal without leaking. Every sealer ive tried always just comes off the plastic and leaks water everywhere. I've tried bath and shower caulking, aquarium and marine sealant, and windshield urithane. Nothing works, its like it just doesn't want to stick to the plastic even though all are graded for plastic and under water use.
    So now I'm trashing this whole tote idea and I'm now thinking of maybe an old chest freezer. First off, how do I go about sealing it for the heat element and such? Also how would I make it weather proof? Id have to keep it outside with that large of a set up. I wouldn't want rain to get into the wiring and cause issues. Please could someone help me out here before I waist more money? I have to buy a new element, drain, and possibly thermostat cause idk how I'm going to get the urithane off :(
     
  3. Oct 15, 2016 #2
    Sea Wolf

    Sea Wolf Well-Known Member

    14,141
    2,262
    Taxachusetts
    Not sure what kind of tote you were using. Did it have any flex to the sides? A chest freezer would be better due to the insulation it has. Put up a picture of what you have for a tote. The solution might be as simple as getting fittings from a plumber. You would use the metal fittings and then seal those.
     

  5. Oct 15, 2016 #3
    breeze

    breeze Member

    264
    0
    Mason, Texas
    Like Seawolf said. It may be as easy as grommets and or compression fittings.
     
  6. Oct 15, 2016 #4
    Headshed

    Headshed New Member

    97
    4
    Western Pennsylvania
    They make oversize drain kits for the Rubbermaid stock tanks. It has a flange on each side, the plug screws into the flanges which pulls them together and seals. A hot water element can screw into those bung plugs as well. An option for sealing is black RTV. Not sure which tote you have but some that look like plastic or rubber are actually a poly foam which is hard to adhere to and can have issues with the heat from the element housing itself.
     
  7. Oct 17, 2016 #5
    WolfGirl

    WolfGirl Member

    615
    3
    Kirksville, Missouri
    I now have a chest freezer. However it has some rust on the inside. Should I seal it with something? I think this will be much easier to work with.
     
  8. Oct 18, 2016 #6
    Headshed

    Headshed New Member

    97
    4
    Western Pennsylvania
    Yep, definitely seal it. The rust will affect soaking skulls, just imagine the color of rust water, you don't want white skulls soaking in that. I'd wait for someone to suggest something they've used to know what will stand up to constant water, steam, and temp fluctuations. If nobody responds I'd first consider an apoxy, even something like a fiberglass resin would be a good bet. Past a resin, options could be a marine paint, an engine paint, and possibly even something like a spray on bed liner. But without trial, i wouldn't be confident with those last few lol.
     
  9. Oct 27, 2016 #7
    bucktown bugs

    bucktown bugs New Member

    10
    0
    Michigan
    My simple way i use is the single stove burners. I have five of them set up with a galv bucket. You can regulate the temp to be exactly what you need and i have a hi temp thermometer that clips on the side to see what temp is. I havent had any issues except for tripping circuit breakers when they are all on.
     
  10. Nov 3, 2016 #8
    chamonix

    chamonix Member

    61
    0
    Wyoming
    http://www.taxidermy.net/forum/index.php/topic,262034.msg1857168.html#msg1857168

    This is helpful link.

    I used automotive gasket maker silicone.